BMX grips

[Mikey]

today i got my animal grips and i put some soap to slip them on and let them sit so the soap would harden. but it didnt i woke up this morning and they are still moving alot! how do you get then from moving around?

 

[Mike Montgomery]

Dont use soap....
Hair spray works.
Or just do it dry.

Soap wont harden that quick.

 

[JonnyJonDogg]

HAIRSPRAY

 

[Joe Manson]

Meh, i use water, then when the grips are on, roll them back and dry the water of them with a hair dryer, works well

 

[Rob.]

i use DUO spray adhesive.
comes off with disinfectant.

 

[Remco]

I use a aircompressor (is it called like that? like, its a tank wich is pumped to like 200psi and air blows out really hard)
I put on the small thingy, and put the grip on for about 1" and put the small thingy under the grip and let the air expand the grip so you can slip it on to your bars. Works every time.

 

[ErikHoward]

does hairspray take long to dry? is it faster than water?

 

[Griffin]

I put the hairspray on at like 9 at night, woke up at 10, it was dry.

 

[Peter Luce]

use wd-40. i used it and my grips slipped on right a way and they dried 10 seconds later. theyve been fine since.

 

[salezone]

i use deodrant, and it smells nice after

 

[Scott Trainer]

i use hairspray or wd-40

 

[guitarman_321]

I use a aircompressor (is it called like that? like, its a tank wich is pumped to like 200psi and air blows out really hard)
I put on the small thingy, and put the grip on for about 1" and put the small thingy under the grip and let the air expand the grip so you can slip it on to your bars. Works every time.

Works good
dont have to wait for anything to dry
takes like 5 seconds

 

[Steve Moore]

Hairspray

 

[domd]

Take them off and spray clearcoat in them dries reall fast.

 

[MattThomMakesMeWarmInside]

if hairspray doest work for some reason put lots of electrical tape around the bare bar then hairspray that

 

[Jdbug_rob]

i never use anything when getting grips on, just man up and push em on, works so much better, and you have no throttle.

 

[mat]

LOL SOAP IS THE WRONG THING TO USE

paint, glue, hairspray, and jizz all work well.

 

[conordavidson]

Use zip ties, it is the BEST method no matter what anybody says. Basically, slide 5 or so zip ties in the grip and spread the evenly around the inside. You MUST keep the side with the square thing on the zip tie, facing out of the end of the grip, not the flange side. Then, push the grip onto the bar with the zip ties still inside. It should slide on pretty easy. Then, once the grip is in place, pull the zip ties out, one by one. Takes about 2 minutes, NO throttle grip, no waiting for the liquid to dry, and no blisters from sliding the grip on without anything.

 

[metrocardscheme]

do the hooood tech. ok get 3 knifes. and stick them in the grips. play with it and get it outtt

 

[scootcb]

Use zip ties, it is the BEST method no matter what anybody says. Basically, slide 5 or so zip ties in the grip and spread the evenly around the inside. You MUST keep the side with the square thing on the zip tie, facing out of the end of the grip, not the flange side. Then, push the grip onto the bar with the zip ties still inside. It should slide on pretty easy. Then, once the grip is in place, pull the zip ties out, one by one. Takes about 2 minutes, NO throttle grip, no waiting for the liquid to dry, and no blisters from sliding the grip on without anything.

i have no idea what you mean. tutorial needed to understand. i mean i get it. but never think it would work..so when you get new grips vid tape it please.