Lock now !

[Kroto]

ok so i got a new 110 eagle sig wheel, i had to hammer in the bearins and it turns out one of my bears are fucked and i can not get it out iv been tring for like 40 mins and i eneded up taking off the seal and ripping out the case thing i can not get it out please help please please please

 

[Kroto]

Bump please help i am getting so angry

 

[mason buckley]

do you have one bearing out?

 

[Kroto]

no they are both stuck in!

 

[Jon.]

do you have a spacer in?

 

[Kroto]

yes i do, btw i had to hammer the bearings in so hard like i mean hard and now they wont come out.. please help i hope i dont fuck my wheel

 

[Jeremy Dalgliesh]

you get a allen key or screw driver nad put it in than get a hammer or mullet than just hit it out or you can use a skateboard truck if u have one

 

[Kroto]

i dont have a sb truck and iv tried hammer it out will not work !!! fuck ! what else can i do?

 

[Kroto]

bump please i really need help could i like take it to a shop or something ?

 

[Jeremy Dalgliesh]

yea take it to a skate shop or put it on the skate truck threads and try to pull it off might work.

 

[zak.]

ive had a problem like this before this is what i did , ps it worked for my but i will accept no responsibility if you fuck it up ..try if you dare
this is a laaast resort !!!!

what you need
needle
very thin screwdriver
thicker screw driver
needle nose plyers

ok your bearing should have a metal shield
get a pin , go round outside of bearing find the C clip , hook it out then remove shield
normally there will be a piece of rubber in there that holds all the balls uses needle nose plyers to pull out
then uses thin screwdriver to get all the ball bearings to one side then put big screwdriver in middle race and lever it .... !POP!
ball bearings will go every were now you have space to get a screwdriver and hammer out outer race plus its easier to get out outer bearing as-well now .

only do this if you have spare bearing , once you do it it can never be used again !

 

[TUC]

ive had a problem like this before this is what i did , ps it worked for my but i will accept no responsibility if you fuck it up ..try if you dare
this is a laaast resort !!!!

what you need
needle
very thin screwdriver
thicker screw driver
needle nose plyers

ok your bearing should have a metal shield
get a pin , go round outside of bearing find the C clip , hook it out then remove shield
normally there will be a piece of rubber in there that holds all the balls uses needle nose plyers to pull out
then uses thin screwdriver to get all the ball bearings to one side then put big screwdriver in middle race and lever it .... !POP!
ball bearings will go every were now you have space to get a screwdriver and hammer out outer race plus its easier to get out outer bearing as-well now .

only do this if you have spare bearing , once you do it it can never be used again !

he already said the bearings are fucked and thats why he needs to get them out so i dont think he will care, allthough really none of this would have happened if he had of just quickly made a bearing press instead of hammering them in...

 

[MarkM]

i sprayed mine with wd40 and started hammering and it came right out

 

[Kroto]

he already said the bearings are fucked and thats why he needs to get them out so i dont think he will care, allthough really none of this would have happened if he had of just quickly made a bearing press instead of hammering them in...

how do you make a bearing press?

 

[ConnorD]

you can make a bearing press by taking an axle and a bunch of old bearings. put like 2 or 3 on each side of the wheel and tighten the axle.

 

[Kroto]

Thank you, il be doing that when i get this fucking bearing out...

 

[matr!]

Sit the wheel on a brick, so that the bearing is lined up with the hole in the brick, then shove your allen key in and hammer the fuck out of it. It worked for me and mine were stuck in like a chode. Just make sure you move the allen around the bearing aswell, don't keep hitting the same spot. It might not feel like it's working but have patience and it will.

 

[Kroto]

ok i got the inner race and the balls bearings out now i need the inner race out, if i can't get it out il post agian thanks,

 

[Jeremy Dalgliesh]

do u mean the outer race if the outer race is stuck then its a bitch to get out

 

[risser]

^its really not. you just have to put a flathead under the little lip of the ring and stomp on the handle of the screwdriver a few times and it should pop out