The Gnar Bar

Status
Not open for further replies.
Kc Corning

Kc Corning

Bronze member
So I was at my buddie Justin's the other night just chillin and we were sitting inside watching TV. I got bored and wanted to mess around on my Scoot out side since I keep my Scoot in my trunk. So as I go out side my buddie's like "do some tricks dude" and I'm like "k?" then as I am shred'n out front, my buddie's mom and her boy friend come out side to watch. So while I was in the middle of this little "demo", Byron (Justin's mom's boyfriend) started to ask me questions about my scooter. I told him the tale of the RAD Handle bar and how alot of kids have these, but they dont make them any more. So he said "hell, I'm looking for a new project. (as if he invensts in some small business's like a scooter company) He's like " I've been on vacation for 2 months. You think we could make these bars? So then I said "yes. Its a simple and strong concept" (talking about RAD Classic 2pc bars)

Therefore I might be coming out with a new RAD style handle bar called The GNAR BAR. It would come Powder Coated and Heat Treated 4130 Chromoly and would be a little thicker too so there is no bending. Byron wants them to be like the "Cadliac of Scooters" (Simply the best you can get)
Cost: around $50-$70 depending on how much they are to make and WILL BE INTERNATIONALY AVALIBE! Just look at BMX handle bars. they go for $50-150.

Hint: this means that Trick Kick might come back. And I was thinking about changing the name to Trick Scooters. So look for the new Gnar Bar by Trick Scooters sometime in the near future. Byron was talking about getting some sample prodotypes made next week. So maybe soon!

If you have any more questions simply IM me.

KC
 
D

Dylan Kasson

Steel Member
the only advantage over rad bars I see in these is they are going ot be power coated which means you couldnt chip off the paint with your fingernail whihc you can on coreys spray paint jobs when they come out i mihgt order some my rad bars are a bit tall and i dont have any way of cutting them
 
S

Steezeman

Administrator
Dylan said:
the only advantage over rad bars I see in these is they are going ot be power coated which means you couldnt chip off the paint with your fingernail whihc you can on coreys spray paint jobs when they come out i mihgt order some my rad bars are a bit tall and i dont have any way of cutting them
Click to expand...

Use a hacksaw or a Dremel.
 
D

Dylan Kasson

Steel Member
Pirate Alex said:
Dylan said:
the only advantage over rad bars I see in these is they are going ot be power coated which means you couldnt chip off the paint with your fingernail whihc you can on coreys spray paint jobs when they come out i mihgt order some my rad bars are a bit tall and i dont have any way of cutting them
Click to expand...

Use a hacksaw or a Dremel.
Click to expand...
isnt it like almost close ot impossible to cut straight with a hacksaw?
and then after that how would I cut the slits?
if i just cut like a notch wiht the hacksaw it wouldnt be wide enough
 
M

Miles Quirk

Member
get a band saw ftw.

i wanna see some of these. considering they cost mroe than a whole scooter (good luck selling them) before i buy any
 
B

Brian Boston

I got myself banned.
Pirate Alex said:
Dylan said:
the only advantage over rad bars I see in these is they are going ot be power coated which means you couldnt chip off the paint with your fingernail whihc you can on coreys spray paint jobs when they come out i mihgt order some my rad bars are a bit tall and i dont have any way of cutting them
Click to expand...

Use a hacksaw or a Dremel.
Click to expand...
I'd go with a pipe cutter and somone whos good with tools, they can usually line stuff up good.
 
S

Steezeman

Administrator
Brian Boston said:
Pirate Alex said:
Dylan said:
the only advantage over rad bars I see in these is they are going ot be power coated which means you couldnt chip off the paint with your fingernail whihc you can on coreys spray paint jobs when they come out i mihgt order some my rad bars are a bit tall and i dont have any way of cutting them
Click to expand...

Use a hacksaw or a Dremel.
Click to expand...
I'd go with a pipe cutter and somone whos good with tools, they can usually line stuff up good.
Click to expand...

Meh, be a man. And ruin your Rad bars while you're at it haha.
 
Travis House

Travis House

Wu-Tang Master
Staff member
I used a hack say to cut another slit in my rads. make one cut, then make one more really close to it then break off the piece between the cuts. Worked perfect
 
Status
Not open for further replies.
Top