Best way to raw a deck

[Stackies]

So I wanna raw out my district V2i, Whats the best way to do it? I can't really afford to sand blast it so what are some other options?

 

[Hunter Treviranus]

stripper in a can ( best stuff)

 

[Victor C.]

i was just wondering the same thing. can you use paint stripper if it is liquid coated (like my nitro is)? will it work? or leave stuff behind?...

 

[Stackies]

I Searched last night and people were saying to use Paint stripper and a wire brush so I might try that, I just don't want to fuck anything up.

 

[carljr]

paint stripper and a wire brush should work

 

[nick silverman]

what color is it and is it jordans ?

 

[Stackies]

No and it's green.

 

[nick silverman]

are you going to run it ?

 

[cody]

Just use paint stripper, then if you have one. Use a pressure washer it will make the paint fly off easy, or just use a hose. I recently just rawed my DH frame so I know some tips.

 

[Cullen]

use some paint stripper, a hose and some sand paper and it should look like this my bro did it around a week or two ago.

bros rawed by CullenPhotos, on Flickr

bros rawed by CullenPhotos, on Flickr

 

[NickTrella]

use "aircraft stripper"

careful though, it will burn through gloves. out of all the stuff ive tried, its best stuff to strip paint with. and yea you can use a wire brush, it speed up the process

 

[Devlyn]

Power sander.

 

[Bennett_J]

Grind... Alot

 

[Jossy]

what about the oven cleaner trick?

 

[ConnorD]

what about the oven cleaner trick?

That only works to remove anodize

 

[Broccoli1]

Jasco Premium Paint & Epoxy remover which you can purchase at Home Depot.

This stuff is seriously caustic and will burn your skin if you get some on you.

I'm not being an over cautious Dad on this one- the shit removes Paint and Epoxy- it WILL burn you- just a tiny little drop.

Be very careful using a wire brush since you'll be slinging the paint remover all over the place with every motion of the wire brush.

YOU DO NOT WANT THIS STUFF IN YOUR EYES​

You'll need a pair of good rubber gloves, a bag of Chip brushes (the cheap throw away brushes)

Apply the remover and let it do it's job- it will start to bubble up
the Paint in about 10-15 mins then carefully scrape the paint off and wipe the removed paint off of the scraper. I usually have a cardboard box to put all the paint in so I use the edge of the Box.

Wash the deck off with a hose thoroughly and repeat.

 

[ashcanscoot]

angle grinder paint strip atachment worked for a pair of bars

 

[Stackies]

Jasco Premium Paint & Epoxy remover which you can purchase at Home Depot.

This stuff is seriously caustic and will burn your skin if you get some on you.

I'm not being an over cautious Dad on this one- the shit removes Paint and Epoxy- it WILL burn you- just a tiny little drop.

Be very careful using a wire brush since you'll be slinging the paint remover all over the place with every motion of the wire brush.

YOU DO NOT WANT THIS STUFF IN YOUR EYES​

You'll need a pair of good rubber gloves, a bag of Chip brushes (the cheap throw away brushes)

Apply the remover and let it do it's job- it will start to bubble up
the Paint in about 10-15 mins then carefully scrape the paint off and wipe the removed paint off of the scraper. I usually have a cardboard box to put all the paint in so I use the edge of the Box.

Wash the deck off with a hose thoroughly and repeat.

I recently Raw my bars and I got aircraft stripper is that any good for a deck? If not I'll defiantly try out what you suggested.

 

[nick silverman]

hey ill trade you my pheonix for your v2i

 

[Victor Saldarriaga]

Sand blastaaaaaaaaaaaaaaaaaaaa

 

[kyle likes to scoot]

are you retarded?