Grind Box plans

[Dean Bost]

http://www.plans4ramps.com/ramps/view/simple_box

only 85$ and the dimensions seem really good. I am definitely making this during the week

made this today , dimensions are 8" long, 2" wide, 1" tall

 

[tyler_magro]

make it wider and lower

 

[issac p]

ive seen a better design before. the top was a solid sheet of uncut plywood. the frame was made entirely of 2 by 4's. using this design you can get a bigger size, and still maintain a low cost.

 

[Grant Schofield]

2ft will be wayy to tall. 2ft wide is lertty good so i suggest making it a bit lower

 

[issac p]

i would make it 12-18in. high

 

[Garrett B]

2 foot tall is good for a grind box. It will be difficult to combo anything with manuals because its higher than a manual pad which would be 1-1.5 ft high.

 

[Robert]

2 foot tall is good for a grind box. It will be difficult to combo anything with manuals because its higher than a manual pad which would be 1-1.5 ft high.

2 feet tall? No If you are making it to learn tricks, then have it 8-12 inches, anything higher sucks for learning.

And use this plan. http://diyskate.com/ledge_01.html

 

[Garrett B]

read what i said after that you dumbbutt robert stineeeeeeeeeeee

 

[dpnelson31]

My box is 10 inches which is way too low. 24 inches high is fine really.

 

[Grant Schofield]

My box is 10 inches which is way too low. 24 inches high is fine really.

no its not and 1.5 is huge too, my box is 1.5 feet talland i cannot nose manual on it, if i could redo it id make it a little bigger then 1 foot, becasue i want to be able to over crook and nose blunt on it.


http://www.youtube.com/watch?v=fZs-Tv3liMI

this is my box its one foot six inches x 2 feet wide

 

[tyler_magro]

The grind box is too damn high

1-1.5 is good imo

 

[Garrett B]

yeah, me and my blader friends made one and we made it like 2 ft tall. It's fucking hard to nose manual. but it's the best grind ledge everr.

grind ledge=1.5-2 ft
manual pad/grind ledge=.5-1 ft
manual pad=a couple inches

 

[tylerbillman]

I have a foot high grind box and I wish it was taller haha. But then I couldn't really learn tricks into grinds whenever I get around to that... so I'd say about a foot tall is good.

 

[matr!]

Grab two shipping crates, you can nick them from industrial places. Glue and screw one on top of the other and nail some plywood to the top. Get some 20x20x3 angle iron from the steel works (it's like 5 bucks) and glue and screw it to the longest edge(make sure to counter sink).

10 minutes and 10 dollars later you have a grind box.

 

[Dean Bost]

these plans would make the dimensions 8 feet long by 1 foot tall by 2 feet wide i believe...

 

[dpnelson31]

no its not and 1.5 is huge too, my box is 1.5 feet talland i cannot nose manual on it, if i could redo it id make it a little bigger then 1 foot, becasue i want to be able to over crook and nose blunt on it.


http://www.youtube.com/watch?v=fZs-Tv3liMI

this is my box its one foot six inches x 2 feet wide

I guess it is all preference and opinion.

 

[Victor C.]

no its not and 1.5 is huge too, my box is 1.5 feet talland i cannot nose manual on it, if i could redo it id make it a little bigger then 1 foot, becasue i want to be able to over crook and nose blunt on it.


http://www.youtube.com/watch?v=fZs-Tv3liMI

this is my box its one foot six inches x 2 feet wide

Sick riding dude!

 

[KyrinBingaman]

Pallets connected with angle iron. Ghetto lyfe.

 

[matr!]

Pallets connected with angle iron. Ghetto lyfe.

And you know it. Just got to nick another crate to finish off this bad boy. My other one broke so I used it as a base for a bonfire.

 

[Bear Grylls]

Just whatever you do don't make it Casey dehaven grind box status