lock folding mech

[timtim2493]

what are all the peices i need and how much are the peices?

 

[Big L]

bolts 3 of them like 2$ for all

 

[daltonkennon]

lol, you need
2 - 5/16x2 1/2
2 - 3/8x2 1/2
some nuts, washers, and tools.
very cheap, definitely not more than $5 if you have all the tools.

you might want to search because i am not 100% sure, and this thread is a waste of time.

super modding thread dude.

 

[gil_]

u need

2-5/16 bolts (3 1/2 inches long)
1-3/8 bolt (3 1/2 inches long)
4-5/16 washers
2-3/8 washers
and all the right sized nuts for each of the three bolts

 

[Derek Scootz]

u need

2-5/16 bolts (3 1/2 inches long)
1-3/8 bolt (3 1/2 inches long)
4-5/16 washers
2-3/8 washers
and all the right sized nuts for each of the three bolts

exactly

and it will cost at most 7 dollars prolly

 

[DaNnYc]

2 3/8 bolts 2 1/2 inches long
1 5/16 bolt 2 1/2 inches long
2 washers for every bolt

 

[daltonkennon]

yeah dude, i used 2 1/2 inch bolts. 3 1/2 seems too big.

go for grade 8 steel if you want it strong, only a little more expensive.

 

[Stantheman]

http://scooterresource.com/e107_plugins/forum/forum_viewtopic.php?272699

 

[NateShewell]

on the plate on the bottom front of the scooter kind of behind the wheel there is a hex wrench nut and bolt you can just tighten that and you wont need to spend any money

 

[YODA_01_01]

on the plate on the bottom front of the scooter kind of behind the wheel there is a hex wrench nut and bolt you can just tighten that and you wont need to spend any money

on a A model the bar bends after a while. also your bars will get lose again

 

[Steezeman]

Don't do what Nate said, that's a really dumb idea. Your bars will keep getting pushed back and your foldy/neck will get all worn down, just spend the $1.50 on bolts and bolt it.

 

[NateShewell]

i did that like a year ago and havent had any problems... its just a cheapskate way

 

[asianpuff16]

]

u need

2-5/16 bolts (3 1/2 inches long)
1-3/8 bolt (3 1/2 inches long)
4-5/16 washers
2-3/8 washers
and all the right sized nuts for each of the three bolts

exactly

and it will cost at most 7 dollars prolly

Lol i paid 88 cents for all of it at
a hardware store :]

 

[kolbycrouch]

i use 2 3/16x2 1/2 and 1 1/2 by 2 1/2 in da back yo

 

[Hep Greg]

on the plate on the bottom front of the scooter kind of behind the wheel there is a hex wrench nut and bolt you can just tighten that and you wont need to spend any money

on a A model the bar bends after a while. also your bars will get lose again

does it really? ive never had that happen before.

 

[latinoboy69]

well ur luky my stock bars woble like hell

 

[todd]

your stocks dont wobble that much but i dont have to worry bout that trolley pole <3

 

[Eric Magray]

super modding thread