SCOOTER FORK SUPER-THREAD!! all your scooter fork questions answered!!!!

[BrandonWeir]

can you ride a french id fork on a madd gear pro deck witout it bein fukn wierd?

on inward it says this:
*NOTE: MPG decks have a headtube that is about 1 inch shorter than most other decks. This means that currently available aftermarket parts such as forks and compression sets may not fit.

Yes, you can. You can ride any fork on an MGP deck, but you either have to cut your forktube down about an inch, or get a really long shim and run HIC.

 

[devinthedew2]

put the new FID forks on here

 

[.Gerrit]

bluntbluntbluntbluntdistrictbluntbluntbluntbluntdistrictbluntbluntbluntphoenix

 

[atown shreddars]

Are ls v2s anygood

 

[louis.e]

lsv3 ??

 

[Maz.]

I don't think so if you want a good fok get tsi thomcat never been broken.

 

[Kelby Lewis]

So I just recentley bought this setup

http://www.east2westscooters.com/app...s/show/2002783

Is there anyway I could still get a Proto striker/fsa headset/proto scs/baby scs. In the future.. I hope this was a proper place to put this..

 

[Jobo Taylor]

Blazer threadless forks? Opinions and pro's/con's?
http://www.doggscooters.com/eu/images/BLAZER ALU BLACK.jpg

 

[DillonMitchell]

i have inward extreme forks and i cant tighten my wheel fully... its either my bolt is to short or my forks wont move inward and i've tried to put a washer in there but it wont go....

 

[mike billick]

is pro comps zero off set for any good cuz i need another zero offset fork what would you guys recomend

 

[austincats]

alright im kinda getting pissed off. i got my ultra pro and the wheel rolled fine and tight with the stock axle and wheel. i now have a fleur de yak wheel and qcs pegs on it. if i run the wheel tight, it barely spins and makes a rubbing sound.if i run the wheel loose it spins but sounds like shit because the wheels rattling around. what can i do to fix it?

 

[Maz.]

You've probably screwed up the bearings by tightening them too much.

 

[austincats]

theres nothing wrong with the bearings when i take the wheel off

 

[Maz.]

You might have ovalised the bearing slot.

 

[Scootin91]

What would u recommend a Lucky NW or a dsa HD

 

[R-Dubya]

Both decent forks. Lucky NWs WILL rust pretty easily if you don't clear them or keep your scooter in your house. DSAs come black powdercoated. NWs are a lot thicker but DSAs are gusseted like ultra pro forks. Basically just comes down to personal preference, I for one think that NWs look a lot better than DSAs.

alright im kinda getting pissed off. i got my ultra pro and the wheel rolled fine and tight with the stock axle and wheel. i now have a fleur de yak wheel and qcs pegs on it. if i run the wheel tight, it barely spins and makes a rubbing sound.if i run the wheel loose it spins but sounds like shit because the wheels rattling around. what can i do to fix it?

You NEED bearing spacers in your wheel on a scooter. I'm 95% sure you aren't running any, judging from your description of the problem.

 

[Scootin91]

Both decent forks. Lucky NWs WILL rust pretty easily if you don't clear them or keep your scooter in your house. DSAs come black powdercoated. NWs are a lot thicker but DSAs are gusseted like ultra pro forks. Basically just comes down to personal preference, I for one think that NWs look a lot better than DSAs.

Alright thanks alot man!

 

[Scootin91]

Well out of the LS and the NW wich would u recommend

 

[Scootin91]

and how are district forks?

 

[heyhey]

what fork would you guys suggest between proto striker or proto senior?