STRIKER FORK. BRASS KNUCKLES PROBLEM!

[spitfire0453]

MY BRASS KNUCKLES WONT SLIP ON MY STRIKERS I HAD TO HAMMER IT ON AND I COULDNT ALLIGN IT SO I HAD TO HAMER IT OFF AND NOW ITS ALL FUCKINGG CHIPPED UP WHAT DO I DO

 

[JGOOD]

this happens with all forks when u first put them on after the first couple of times it stops doing this and becomes easier, you should have used a rubber mallet and protect it with like wood or something so it wouldnt have chipped. I had the same problem with my inward forks but it works fine afterwords.

 

[Brian Murphy]

the penny trick you take the bolts out but them backwards and pu a penny in the slip strengthening the clamp grip to fit over the tube then u on screw it when its alining making it even tighter then you screw it up and your good

as madis would say
GREAT SUCCESS


/THREAD

 

[spitfire0453]

Do you do it to all the bolts Brian?

 

[JDBen]

i heard that they fit very tight anyway

but sounds like a good idea to stretch the SCS

 

[Brian Murphy]

when i did it i used 2 bolts one at the top one at the bottom and i also tighten the compression before unscrewing the bolts that are with the pennies and it well hold mad good mine still haven't loosened and my older knuckles never came loose for 3 months until i took it off for the baby

 

[spitfire0453]

I cant tighten the bolt to stretch it , fuckingg strips the shit out of everything

 

[Brian Murphy]

you don't stretch it you put the screws on back words slowly tighten it till it gets on the fork its not gong to fuck it up unless you try to fully stretch that shyt

 

[spitfire0453]

I put them in backwards but theyre not made to go backwards so it's to hard to tighten past a certain point

 

[joeyamos]

i had the same prob but idgaf now

 

[Matthew Madera]

you don't stretch it you put the screws on back words slowly tighten it till it gets on the fork its not gong to fuck it up unless you try to fully stretch that shyt

murphy helped me do it , and it worked

 

[Lil Steve]

It happend to me too. If you have a rubber mallet just use that or stretch it like Murphy said.

 

[take2industries]

WD-40 yor fork, and get a flat tip and stretch it loke that and pput it on, after its one about a 1/2 inch , then just hit it with a rubber hammer.,

 

[MattThomMakesMeWarmInside]

MY BRASS KNUCKLES WONT SLIP ON MY STRIKERS I HAD TO HAMMER IT ON AND I COULDNT ALLIGN IT SO I HAD TO HAMER IT OFF AND NOW ITS ALL FUCKINGG CHIPPED UP WHAT DO I DO

YOUR CAPS MAKE IT SEEM AS THOUGH YOU ARE YELLING LIKE BILLY MAYS

 

[Jason]

If you have to resort to using a hammer on anything other than starnuts, you're doing it wrong.

 

[take2industries]

not true. the brass knuckles are hard to get on the first couple times

 

[zolof]

MY BRASS KNUCKLES WONT SLIP ON MY STRIKERS I HAD TO HAMMER IT ON AND I COULDNT ALLIGN IT SO I HAD TO HAMER IT OFF AND NOW ITS ALL FUCKINGG CHIPPED UP WHAT DO I DO

YOUR CAPS MAKE IT SEEM AS THOUGH YOU ARE YELLING LIKE BILLY MAYS

TOO SOON TO MAKE FUN OF HIM
RIP BILLY

 

[spitfire0453]

IT WORK'S FINE NOW!!! Anyway's I still have to use a rubber mallet to put it on and take it off which is a fuckingg pain. And dont stretch ur scs bolt's are not ment to go in that way, it will strip your scs.

 

[Rob.]

If you have to resort to using a hammer on anything other than starnuts, you're doing it wrong.

God forbid you're using it with a screw driver to take out your headset.
Or pry out some stuck foldy bolts.
Or tap in some stubborn foldy bolts.
Or tap in... Brake bolts?
Put bearings in, the lazy way?

 

[ashz893scootys]

i hope this dosent happen when i get my scs