FS: Square (pirate) reinforcements

M

me1

Member
Alex, when you make these reinforcements do you cut them flush to the metal behind/below the folding mech? I plan on getting reinforcements when I start to need them, but I still want to be able to to the pegless icepick thing that I do, and I figure it would make them easier to get into but if it isn't flush I think I'm going to be off set when I do them. So yeah, are they cut flush?

Edit I see on your second picture that they are flush, but I wonder if you just did that for yours. Thats where I'm wondering.
 
S

Steezeman

Administrator
What do you mean? I'm kinda confused. All I do when I make them is cut the pieces of metal at the ends and drill holes. Since there's a little overhang on the deck it isn't totally flush, but it won't mess you up at all.
 
E

ENERGY TURTLE

Member
Pirate Alex said:
What do you mean? I'm kinda confused. All I do when I make them is cut the pieces of metal at the ends and drill holes. Since there's a little overhang on the deck it isn't totally flush, but it won't mess you up at all.
Click to expand...

Im pretty sure he means how you angled yours at the front to be flush with the angle at the fornt of the deck. And Im wondering the same thing.
 
M

me1

Member
In your second picture, you cut yours flush, I am wondering if you just did that for your own or if you do it for all. I see it isn't perfect but that little bit won't mess me up. Hopefully you understand.
 
Chase Robertson

Chase Robertson

Bronze member
questions, would i need to drill holes in my scoot? cus i was a little unclear on that

and you mean the spacers that are on the outside of wheels inside the deck on bs? or what ones...
 
S

Steezeman

Administrator
No, you don't have to drill or mod your deck at all. And the only thing you need to get is old wheel spacers from old B's, Pros. And they go inside the reinforcements in the back.
 
P

P4RK3R

Member
fashow69 said:
oh soo alex decides to do this and its the coolest shit ever??? i tried to do this along time ago for you people and yall didnt even give a shit.
Click to expand...
yeah, me too, but mine were steel, not aluminum
 
P

P4RK3R

Member
Shelby Grimnes said:
your retarded brandon, its cost a lot of $$$ to get that kind of tubing
its like 40 dollars at lowes hardwear i saw it when i got bolts for my scooter
Click to expand...
really? at my lowes a 3ft piece cost $8.50 and a 4ft. piece cost $10.50
the huge and thick metal angle iron for grinding boxes/manual pads cost about $34...
 
P

P4RK3R

Member
i know its a tripple post...
but can you make me one for a B deck?
and i don't need washers or anything, just the back axle bolt
 
P

P4RK3R

Member
Pirate Alex said:
Yeah, are you sure you don't need two bolts? One for the front and the back? Or would you drill the front hole?
Click to expand...
i will drill the front hole, and i allready have a bolt for the front from my steel reinforcements.
i just need a grade 8 bolt for the back, because i bent my last ones(they were some crappy bolts)

but i will need you to drill the hole in the front of the reinforcements, so i will know where to drill into my deck to make it straight.

and i have hundreds of spacers and washers and locknuts, so i'm covered on that part


EDIT:
and ill have to take out my pins for these reinforcements...

will it be worth it?
 
Hep Greg

Hep Greg

Administrator
alex my reinforcements are starting to get all beat to hell... i might be buying some new ones from you in the near future.
 
You must log in or register to reply here.
Top