Plastic on the pro model folding mech

S

S_O_R_D

Member
hey i just got my new pro model and it has a plastic covering on the folding mech and i couldt figure out how to get it off so i could bolt it. Any suggestions? :?

Yeah so how do i make my sig smaller?
 
S

Steezeman

Administrator
Rip it off with pliers or something, you don't need it.

And make your sig smaller too, because it's real big.
 
Kc Corning

Kc Corning

Bronze member
This is how you properly remove that pointless dust guard.

You have the bottom pin and the top pin of the folding system. These pins are held in place by Cur Clips, or C clips. Place the scooter flat on the ground or table. Then take a flat head and ply that bottom pins e clip off. (ItÃ?Æ?Ã?â??Ã?â??Ã?¢Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¡Ã?â??Ã?¬Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¾Ã?â??Ã?¢s going to be a bitch and be VERY careful that you donÃ?Æ?Ã?â??Ã?â??Ã?¢Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¡Ã?â??Ã?¬Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¾Ã?â??Ã?¢t cut yourself, IÃ?Æ?Ã?â??Ã?â??Ã?¢Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¡Ã?â??Ã?¬Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¾Ã?â??Ã?¢ve done that plenty of times)

Once thatÃ?Æ?Ã?â??Ã?â??Ã?¢Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¡Ã?â??Ã?¬Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¾Ã?â??Ã?¢s done itÃ?Æ?Ã?â??Ã?â??Ã?¢Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¡Ã?â??Ã?¬Ã?Æ?Ã?¢Ã?¢ââ??¬Ã?¾Ã?â??Ã?¢s all a matter of getting the compression spring out with needle nose pliers. Then the whole folding mech should come apart. Then just take the plastic off. I had to do that 20 times when I made my pro models. It was a bitch.
 
Kc Corning

Kc Corning

Bronze member
those are the pins. you want to go to the hardware store and get 2 bolts; 3/8" 2/3/4" long top bolt (primary) and a 5/16" 2/3/4" long bottom bolt (secondary) these bolts will replace the pins and make your folding system solid.
 
eirepro

eirepro

Steel Member
I Just Kept whipping, and eventually my big ass shoes snapped them off, so It worked out well for me.
 
G

grantstark

Member
yea haha i landed wrong once and snapped it in half, so i just tore the rest off, and then kicked off the other one it was hella easy to get it for me
 
You must log in or register to reply here.
Top