YOUR SCOOTER

[James Webb]

So clen. What happend with your ethic?

Well the main thing is the rear end is bent so my wheel sits at like 75 degree angle to the ground and its banana'd so it just doesnt feel good anymore

 

[instinctscooter]

got hooked up with a 22 thresh since my ethic is dead

IMG_0739 by JamesWebbyy, on Flickr

is it just me or do you break parts very often? it would be cool to see the ethic in the broken scooter thread, im not trying to derail this thread as i am talking about james scooter

 

[James Webb]

is it just me or do you break parts very often? it would be cool to see the ethic in the broken scooter thread, im not trying to derail this thread as i am talking about james scooter

Unfortunately i do break parts quite a bit, its really annoying.

 

[My_Names_Jordan]

nicest fucking scooter ive ever seen in my life

jassssseeeeeennnnnnn

 

[danielBMXisFUN]

^ that sig gif always makes me laugh i imagine the guy sayin "now for some clips"

 

[DeviinGilly]

fitting heptrons into a proto SCS is the hardest thing I've ever done

edit: is it ok to like, lube this bitch up or something?

 

[Devin DePriest]

fitting heptrons into a proto SCS is the hardest thing I've ever done

edit: is it ok to like, lube this bitch up or something?

Penny trick it bruh

 

[DeviinGilly]

Penny trick it bruh

tried it, but the SCS just goes back to its normal size and i take the penny out.

 

[Devin DePriest]

tried it, but the SCS just goes back to its normal size and i take the penny out.

Keep the penny in when you put the bars on

 

[Phase Three]

tried it, but the SCS just goes back to its normal size and i take the penny out.

dis iz wut i do to me heps

 

[GRAYDONSHEDSSTREET]

View attachment 1231
dis iz wut i do to me heps

This is what I do to my Heps
Don't start

 

[parrish]

sand the paint off of them, and stick a pair of bars that is thinner in while you're coin tricking it so the coin doesn't slip into the slot the bars fit into, thats probably your issue is the coin moves as you tighten and gets in the cylinder where the bars should be and then they don't fit.

 

[DeviinGilly]

last post about me trying to make sure my scooter is prefect.
everything is tight, like really fucking tight, bars are in, grip tape is on. but when i land a trick theres this little buzzing, like a vibrating? it makes it sound super bad.... any ideas?

 

[ChrisFleugel]

last post about me trying to make sure my scooter is prefect.
everything is tight, like really fucking tight, bars are in, grip tape is on. but when i land a trick theres this little buzzing, like a vibrating? it makes it sound super bad.... any ideas?

possibly the brake

 

[DeviinGilly]

possibly the brake

took it off and its still going ):

 

[Phase Three]

took it off and its still going ):

bearings?

 

[thealexbuffery]

took it off and its still going ):

Maybe you wheels, like the bearing spacers? Or maybe just the bearings / wheels

 

[Phase Three]

took it off and its still going ):

check your bar ends

 

[Hcc]

last post about me trying to make sure my scooter is prefect.
everything is tight, like really fucking tight, bars are in, grip tape is on. but when i land a trick theres this little buzzing, like a vibrating? it makes it sound super bad.... any ideas?

If it's not your headset or brake then it's your wheel bearings. Take your wheels off and hit the bearings with a hammer, sometimes they shift slightly and the bearing spacer has just enough room to make a buzzing noise. Legit only has to be out by 1 mm and it will make a noise so just hit them with a hammer and if they're still buzzing it may be that your bearings are corroded away so you will need to replace the bearings and bearing spacers. If you've just put new bearings in then your wheels may be ovalised.

 

[addicted_to_Addict]

Take your bearings out and wrap something like thin Aluminium around it. (like from a beer or smth.)