eaglesport hellllppp

[1126box]

i got 2 new 110mm wheels. i am using a bearing spacer i tightneed as hard as i could and it wobbles when i spin ? help plz

 

[Devon Garcia]

The bearing spacer might be alittle bigger then normal.
Try a new one becouse mine was like that too.

 

[blaine142]

the new eagle bearing slots are made a little bigger so u can get the bearings in easier.

 

[asianpuff16]

put washers on the outside of your axel

 

[Jason]

You may just have rattley bearings.

 

[Mark Abramsky]

its just how eagle makes their wheels

 

[Hep Greg]

honestly i dunno what that could be, cuz they shouldnt wobble like back and forth unless somethnigs put in crooked


i think it might just be the spacer
-margaret

 

[Jamie N]

you can file down the spacer a little bit, if the baearings are sticking out too much.

 

[Remco]

no, dont file it, it will never be perfectly straight, and your bearings will get fucked up.

Ask marcel for the eaglesport spacers, those are high precission spacers, made for eaglesport wheels.

 

[JarradSmith]

thats retarded.

 

[ryanlovegays]

cdhjgfuyvjarradfgbsmithdhgbfrishfbvfgquitefbhvthefhbgay

 

[marcel]

thats retarded.

Maybe you are......

Eagle Wheels are made according a intl. skate standerd and this means that the inside "breast"( thicker alu part between the bearings) is exactly 10.0 mm.(+/- 0,01mm)

If you use stock (read: cheap, not precize) spacers then it can happen that the sizing of this spacer isnt 100% correct since stockspacers aint cnc made, but mostly pressed/stamped (what has a higher tollerance(+/- 0,1/0,2mm then cnc made stuff).
You CAN file down the spacer to 10.1 or 10.2 mm and it will fits fine. IF you cannot do it order some Eagle spacers (CNC made) at your local retailer.

To know IF your spacer is TO wide, check if the wheel goes from left to right sliding over the bearings, if thats so the spacer is to wide.
The opposite is when you tight your wheels and the wheels do not spin, in that case the spacer is to narrow.

Hope this helps.

Marcel

 

[JonnyJonDogg]

i could say i understood all of that but i would be lieing

 

[marcel]

what you didnt understood?

 

[1126box]

where can buy an eagle spacer ??

 

[JonnyJonDogg]

thats retarded.

Maybe you are......

Eagle Wheels are made according a intl. skate standerd and this means that the inside "breast"( thicker alu part between the bearings) is exactly 10.0 mm.(+/- 0,01mm)

If you use stock (read: cheap, not precize) spacers then it can happen that the sizing of this spacer isnt 100% correct since stockspacers aint cnc made, but mostly pressed/stamped (what has a higher tollerance(+/- 0,1/0,2mm then cnc made stuff).
You CAN file down the spacer to 10.1 or 10.2 mm and it will fits fine. IF you cannot do it order some Eagle spacers (CNC made) at your local retailer.

To know IF your spacer is TO wide, check if the wheel goes from left to right sliding over the bearings, if thats so the spacer is to wide.
The opposite is when you tight your wheels and the wheels do not spin, in that case the spacer is to narrow.

Hope this helps.

Marcel

 

[zolof]

whats the point in spacers?
i never use them
never will

 

[Jakee F]

With a spacer you can tighten the shit out of your wheel and it will still spin to the fullest of its ability.

 

[JonnyJonDogg]

yeh your bearings might explode haha

 

[Chase Robertson]

zolof you should definitely use spacers, otherwise your bolts aren't tight enough or your bearings aren't as fast as they could be.