New Part Idea Thread

[Jacobo]

I won't buy because I don't know what it is.

this. if you tell us what you idea is then you will get helpful responses...

 

[michaelpytel]

this. if you tell us what you idea is then you will get helpful responses...

Haha im not asking anyone to buy it im asking if anyone thinks if there was a new type of compresion that is simple, and everything iv said, would you be interested. Not asking anyone to buy it jeez haha i guess it was a bad thin to ask apparently. Ill just see what people think once i het them made

 

[Connorh333]

7075 aluminum deck

 

[Grant Schofield]

Spring compression idea? First I've heard of this.

ok ill try to explain it

so you have a spring and you hav e drill a hole in your fork so you can put a pin trough it so the spring pushes down on the headset and pushes up in the fork.

 

[702_dialed_rider]

i made my own comprsion but it use oversized bars

 

[702_dialed_rider]

http://youtu.be/oDScCrVPzyc

 

[Robert]

http://youtu.be/oDScCrVPzyc

So, its pretty much just hic, but upside down?

 

[702_dialed_rider]

yes and with out hard installation and easier to put together dose not required the rider to install a star nut in to forks

 

[thealexbuffery]

suspension forks for shock absorbing haha, or 2 piece forksso if one part of your fork breaks then you can just replace that part, it gets held on with 2 strong bolts or something like that idk lol

 

[morgan_bvrns]

suspension forks for shock absorbing haha, or 2 piece forksso if one part of your fork breaks then you can just replace that part, it gets held on with 2 strong bolts or something like that idk lol

That just sounds like old two piece FrID forks and stuff. Just pinned.

 

[RiccardoM]

am asking if people would be interested in a convenient compresion system at a very affordable price, to see if anyone would consider trying something that is nothing like HIC or SCS. it doesnt matter how it works right now, im asking who would want somethign like that.

Most convenient compression? The new Sacrifice SCS.

 

[Sam_Hudson]

The first TSI flowmasters had flexfenders built in to the deck plate but they broke off

 

[RiccardoM]

yes and with out hard installation and easier to put together dose not required the rider to install a star nut in to forks

It's already been done. I think most of the compressions have already been combined.

ICS/SCS HIC/ICS Threaded/ICS You can't really combine hic and scs but you get what I mean.

 

[Carson .]

We should arc weld our bars. I don't understand why we tig weld chromo when we could arc weld it. Arc s much easier, would take less time, and its the strongest weld too.

Hahahahahahahahahahahahahahahahahahaha

 

[Dewey]

No hard installation, how about hoc but not starnut just have an ics bolt run to the top and a nut at the end. I've done it before with scs because I didn't have a good starnut but it was a bitch of a process to tighten

 

[Robert]

No hard installation, how about hoc but not starnut just have an ics bolt run to the top and a nut at the end. I've done it before with scs because I didn't have a good starnut but it was a bitch of a process to tighten

http://www.youtube.com/watch?v=P3n0U-VRls0

 

[michaelpytel]

http://www.youtube.com/watch?v=P3n0U-VRls0

I would define that as hard insulation. not because it is difficult but just the fact that it requires so many steps. nor does this compression use any sort of star-nut or HIC shim. Im sorry i brought it up since everyone is too close minded to imagine something outside of conventional compression to understand that its going to be something different so just forget about it till i have my first prototypes.

 

[issac p]

if you tell people that you have a "cool and simple" new form of compression, we aren't going to care until we know what it is.

 

[michaelpytel]

No hard installation, how about hoc but not starnut just have an ics bolt run to the top and a nut at the end. I've done it before with scs because I didn't have a good starnut but it was a bitch of a process to tighten

not all forks can use ICS compression, a compression should be universal, Any fork, and any standard bar. my new compression i am going to make is 100% universal with the respects that Oversized bars were originally designed to be used with HIC, so besides over sized its universal. any standard bar, and any fork will work, nothing like conventional thread less compression.

 

[michaelpytel]

if you tell people that you have a "cool and simple" new form of compression, we aren't going to care until we know what it is.

ok haha that's why i said sorry for bringing it up, i was just asking about the idea of the compression, not it itself but i guess kids cant see what im asking so never mind.