your custom/homemade parts thread

S

SCOOTERash

Member
i love those kucks!
i need help.. i have a trolly bar, well.. i used to have a trolly bar and i cut it down to good peg sized.. pegs! but i need to know how could i put them on my scooter :S lol, any one got any ideas?
thanks
 
C

chrisisafoo

Member
ashz_893 said:
did somone say ghetto knucks?
img_2646.jpg
Click to expand...

Do those have the whole compression setup inside, or they just clamps?

either way BRAVO!
 
J

jare88

Jerry
now that i think about it, all wou would have to do to make a scs is to have some relatively thick metal tubing, a hacksaw(to cut the slit in the back so it can acutally clamp), one small sized drill bit(for the screws), and two different sized large drill bits(one side to fit bars, one for compression cap/forks). holy shitt, that would probably only cost like $20 bucks and a couple of hours. sorry proto. i think i will acutally try this, possibly a tutorial. ghetto knucks ftw nigz

if anyone who already owns an scs can tell me the dimensions it would help a bunch. side to side, front to back, and height are needed. also, it would help if you could tell me the inner diameters for both the bottom and top half. thanks, i would love your help.
 
R

ryankeong

Member
lol what are you going to drill through?? for the bolts. and you cant really just drill a 30 mm hole through steel tubing like that it may work but its a bit more complicated than what you described
 
J

jare88

Jerry
no, i would get a square bar. i don't care too much about the looks, but if i wanted i could easily round off the front edges.
 
ashz893scootys

ashz893scootys

Member
jared (K) said:
no, i would get a square bar. i don't care too much about the looks, but if i wanted i could easily round off the front edges.
Click to expand...
its not as easy as it looks and u gotta thread it so the bolts thread into the clamp
 
Dom Marconi

Dom Marconi

Silver Member
jared (K) said:
now that i think about it, all wou would have to do to make a scs is to have some relatively thick metal tubing, a hacksaw(to cut the slit in the back so it can acutally clamp), one small sized drill bit(for the screws), and two different sized large drill bits(one side to fit bars, one for compression cap/forks). holy shitt, that would probably only cost like $20 bucks and a couple of hours. sorry proto. i think i will acutally try this, possibly a tutorial. ghetto knucks ftw nigz

if anyone who already owns an scs can tell me the dimensions it would help a bunch. side to side, front to back, and height are needed. also, it would help if you could tell me the inner diameters for both the bottom and top half. thanks, i would love your help.
Click to expand...

haha this kid thinks he knows what hes doing
 
JacobUrrea08

JacobUrrea08

Bronze member
jared (K) said:
now that i think about it, all wou would have to do to make a scs is to have some relatively thick metal tubing, a hacksaw(to cut the slit in the back so it can acutally clamp), one small sized drill bit(for the screws), and two different sized large drill bits(one side to fit bars, one for compression cap/forks). holy shitt, that would probably only cost like $20 bucks and a couple of hours. sorry proto. i think i will acutally try this, possibly a tutorial. ghetto knucks ftw nigz

if anyone who already owns an scs can tell me the dimensions it would help a bunch. side to side, front to back, and height are needed. also, it would help if you could tell me the inner diameters for both the bottom and top half. thanks, i would love your help.
Click to expand...
yeah and instead of threading them into the clamp you could just use lock nuts so you wouldn't have to worry about the bolts stripping or anything.
 
You must log in or register to reply here.
Top